Overview:
Klenk's Epoxy Enamel is an extremely hard and durable two-component epoxy for consumer and professional use. It is specially designed to restore the finish on tubs, sinks, toilets, ceramic wall tiles, and appliances. Klenk's Epoxy Enamel can be used on any hard, solvent-resistant surface, such as ceramic, metal, stone, marble, melamine, fiberglass, etc. Do not use on plastic or imitation marble, stove top ranges, or other surfaces subject to excessive heat. Always test surface with Klenk's Epoxy Thinner prior to use.
Getting Started with Klenk's
Step 1: Surface Preparation
CHIPS: Repair surface chips with a 2-part EPOXY filler.
RUST: Sand rusted areas and treat with a rust neutralizer/converter, such as Circa 1850 Rust Treatment.
GROUT: For best results, remove grout prior to painting tiles. Regrout after painting. If grout is not removed, thoroughly remove all traces of grout sealer prior to cleaning, by scrubbing with epoxy thinner and then scrubbing with ammonia.
CAULKING: Thoroughly remove all traces of caulking prior to cleaning, by scraping off caulking, scrubbing with epoxy thinner and then scrubbing with ammonia. Contamination of paint with caulking residue may result in small circles where paint does not adhere (fish eyes). Add 2 drops of Klenk’s Fish Eye Eliminator solution to the paint if fish eyes occur. Recaulk after painting.
CLEANING: WEAR GLOVES. Apply Klenk's Prep #1 Cleaning Compound to abrasive sponge. Rub the Cleaning Compound onto the surface in a circular fashion. SCRUB VIGOUROUSLY with the Prep #1 and abrasive sponge to degloss the surface. Thoroughly scrub area where caulking was removed. Rinse surface thoroughly with warm water.
WEAR GLOVES. Dissolve the TSP powder in 4-8 litres (1-2 gals) warm water. Scrub the surface using the sponge soaked in TSP solution. Thoroughly scrub area where caulking was removed. Rinse surface thoroughly with warm water. Allow to dry completely.
WEAR GLOVES. Apply Klenk's Epoxy Thinner to a lint-free cloth. Wipe the entire surface with Klenk's Epoxy Thinner. Thoroughly scrub area where caulking was removed. Allow the surface to dry completely.
Step 2: Apply Klenk's Epoxy Enamel
Apply masking tape around edges, outlets, handles, taps, overflows, etc. Completely cover taps.
Stir the contents of both cans, Parts A and B, separately. Pour the contents of Part B into Part A. Stir the mixture thoroughly. Close lid. Allow mixture to stand for 1 hour.
1st COAT (BRUSH OPTION): Stir the contents and apply a thin coat of Klenk's Epoxy using a clean, 1" brush. Paint the surface in 6" squares using vertical strokes, smoothing the finish with even horizontal strokes. DO NOT GO BACK AND FORTH OVER PAINTED AREAS. Painted surfacewill look smooth after the second coat.
OR
1st COAT (ROLLER OPTION): Stir the contents and apply a thin coat of Klenk's Epoxy using a high density foam roller. Roller application will yield a textured, orange peel finish. Tip off (lightly drag the brush tip across the surface) with a brush if a smoother finish is desired.
2nd COAT (SAME DAY): Close lid tightly. Wait 2-3 hours prior to applying a second coat. If the surface is still tacky, proceed to 2nd COAT (NEXT DAY) application. Stir the contents and apply a second coat as directed for 1st COAT. Offset each 6” square if using a brush. If necessary, wait a minimum of 2 hours prior to applying a third coat. DO NOT USE IF PAINT HAS BECOME VERY THICK.
OR
2nd COAT (NEXT DAY): Close lid tightly. Place the remaining Klenk's Epoxy mixture in a very cold (less than 0°C) place for approx. 20 hours. Take added precautions if storing in freezer to prevent transfer of odours. Prior to applying a second coat, loosen the lid and allow the mixture to stand for 1 hour to reach room temperature. Stir the contents and apply a second or third coat as directed for 1st COAT. Offset each 6” square if using a
brush.
Step 3: Enjoy Your Revitalized Space
With Klenk's, enjoy the satisfaction of a beautifully restored surface that lasts.
Don't settle for lackluster finishes. Choose Klenk's Epoxy Enamel Paint for a glossy, professional look that rejuvenates your space.
HELPFUL HINTS
CONSISTENCY: Klenk's Epoxy is very thin. Apply thin coats from the top down to prevent runs and drips from ruining whatever is below.
SANDING: You may sand runs or drips once paint is dry, using 400 or finer grit sandpaper.
CLEAN UP: Clean spills and brush/roller immediately after each use using Klenk's Epoxy Thinner. Alternatively, use a new brush/roller for each coat.
CURE TIME: DO NOT USE painted surface for 5 days after painting.
CLEANING: Once cured, you may clean painted surfaces with Klenk's Bare Bath or with dish washing liquid diluted 10 times in water. DO NOT USE products containing caustics, solvents or abrasives.
BATH MATS: DO NOT USE a bath mat for 1 month after painting. Thereafter, remove mat after each use.
DISCOLOURATION: Certain products, such as bath oils, bath beads, food, juice, dyes, and chemicals may discolour the painted surface.
Note for Consumers:
This product is not suitable for plastic, imitation marble, or surfaces that are regularly exposed to high temperatures such as stove top ranges. For best results and to ensure compatibility, we recommend conducting a surface test with Klenk's Epoxy Thinner prior to application.
