Klenk's Epoxy Enamel Bathtub & Tile Paint

Klenks 2-Part Epoxy for Tubs, Sinks & Tile

Klenk's Epoxy Enamel is a hard, durable two-component epoxy coating designed to restore the finish on bathtubs, sinks, toilets, ceramic wall tiles, appliances and other hard, solvent-resistant surfaces.

Its high-gloss, abrasion-resistant and water-resistant finish makes it an excellent choice for refinishing worn bathroom fixtures without replacing them.

Klenk's Epoxy Enamel can be applied by brush, high-density foam roller or spray and is suitable for both DIY and professional refinishing projects.

Why Choose Klenk's Epoxy?

• Two-component epoxy coating

• Hard, durable epoxy finish

• High-gloss appearance

• Abrasion resistant

• Water resistant

• Designed for bathtub reglazing

• Suitable for sinks and toilets

• Suitable for ceramic wall tile

• Can be used on many appliances

• Brush, roll or spray application

• White finish

• Tintable to pale colours

• Two coats recommended

What Surfaces Can Be Painted?

Klenk's Epoxy Enamel can be used on hard, solvent-resistant surfaces including:

• Bathtubs

• Sinks

• Toilets

• Ceramic wall tiles

• Appliances

• Ceramic

• Metal

• Stone

• Marble

• Melamine

• Fibreglass

Always test the surface with Klenk's Epoxy Thinner before refinishing to confirm compatibility.

Where Should It Not Be Used?

Do not use Klenk's Epoxy Enamel on:

• Stove tops

• Heated surfaces

• Surfaces exposed to excessive heat

• Imitation marble

Plastic surfaces may be damaged by the solvents in the coating. Test an inconspicuous area with Klenk's Epoxy Thinner before attempting to coat plastic.

Do not apply over chipped or peeling existing finishes.

Prep Before Klenk's Epoxy

Proper surface preparation is essential for adhesion and a durable finish when refinishing bathtubs, sinks and ceramic tile.

Start with the Klenk's Tub & Tile Prep Kit to thoroughly clean and prepare the existing surface before applying Klenk's Epoxy Enamel. The prep process helps remove contaminants and prepares the surface for proper epoxy adhesion.

Use Klenk's Epoxy Thinner for solvent cleaning, compatibility testing and cleaning application equipment used with Klenk's Epoxy Enamel.

For best results, complete all required cleaning, repairs and surface preparation before mixing Parts A and B of the epoxy.

Surface Preparation

Proper preparation is critical when refinishing a bathtub, sink or tile surface.

Remove all caulking before cleaning. Silicone or caulking residue can contaminate the surface and cause small areas where the epoxy will not adhere.

Repair chips with a suitable two-part epoxy filler.

Sand rusted areas and treat remaining rust with an appropriate rust neutralizer or converter.

For tile projects, removing grout before painting provides the best results. Regrout after the epoxy has cured.

If an existing coating is chipped or peeling, remove it before beginning surface preparation.

Clean Before Applying Epoxy

Swing Paints recommends preparing the surface with Klenk's Tub & Tile Prep Kit and Klenk's Epoxy Thinner.

Thorough cleaning and deglossing are essential because soap residue, oils, silicone, grout sealer and other contaminants can interfere with adhesion.

Allow the surface to dry completely before applying Klenk's Epoxy Enamel.

Mixing Klenk's Epoxy Enamel

Klenk's Epoxy Enamel is a two-component system.

Mixing Ratio: 1 part Epoxy Catalyst to 1 part Epoxy Paint.

Stir Parts A and B separately before combining them.

Pour Part B into Part A and mix thoroughly.

After mixing, close the container and allow the mixture to stand for approximately 1 hour before application.

Pot Life

Once Parts A and B have been combined, the usable pot life depends heavily on temperature.

At approximately 25°C (77°F), the mixed epoxy has a pot life of approximately 6 hours.

The manufacturer also specifies approximately 48 hours at -15°C (5°F).

Do not continue applying the coating once it has become excessively thick.

Brush Application

Use a clean 1-inch brush designed for epoxy coatings.

Apply a thin coat from the top downward to help minimize runs and drips.

When refinishing tubs or similar surfaces, work in approximately 6-inch sections using vertical strokes and then smooth the finish with even horizontal strokes.

Avoid repeatedly brushing back and forth over areas that have already been coated.

Roller Application

Klenk's Epoxy Enamel can also be applied using a high-density foam roller.

Be aware that roller application can produce a textured or orange-peel appearance.

For a smoother finish, lightly tip off the freshly rolled epoxy with a suitable brush.

Spray Application

Klenk's Epoxy Enamel can be sprayed.

The mixing ratio remains 1:1 when spraying.

According to Klenk's application instructions, thinning is not required for spray application.

Ensure adequate ventilation and use appropriate protective equipment when spraying.

How Many Coats Are Needed?

Apply two coats for normal applications.

Additional coats may be required when covering dark colours or when additional build is desired.

For a same-day second coat, wait approximately 2–3 hours.

The first coat should no longer be tacky before applying the next coat.

If another coat is required, wait a minimum of approximately 2 hours before applying it.

Temperature & Humidity

Maintain a minimum room temperature of approximately:

24°C (75°F)

Maintain this temperature during application and for at least 24 hours afterward.

Provide adequate ventilation throughout application and drying.

Do not apply Klenk's Epoxy Enamel during periods of high relative humidity.

Coverage

Approximate coverage is:

6 m²/L

A one-litre kit provides approximately enough material for two coats on a bathtub, sink and toilet, according to Klenk's application instructions.

Actual coverage will vary according to the surface, application method and coating thickness.

Cure Time

Do not use the refinished surface for at least:

5 days after painting

Allowing the epoxy to cure fully before exposing it to water and normal use is critical to the durability of the finished surface.

Colour & Finish

Colour: White
Tinting: Can be tinted to pale colours
Finish: High Gloss

Because tinting can affect appearance and coverage, additional coats may be necessary depending on the selected colour and the original surface colour.

Cleaning After Curing

Once fully cured, clean the refinished surface using a mild cleaner such as diluted dishwashing liquid.

Do not use cleaners containing:

• Abrasives

• Strong solvents

• Caustic ingredients

Aggressive cleaners can damage the refinished epoxy surface.

Bath Mat Precautions

Do not use a bath mat on a newly refinished bathtub for approximately one month.

After that period, remove the bath mat after each use rather than leaving it permanently attached to the refinished surface.

Technical Specifications

Product: Klenk's Epoxy Enamel
Product Code: 8100
Type: Two-component epoxy enamel
Primary Use: Bathtub, sink and tile refinishing
Finish: High Gloss
Colour: White
Tintable: Yes, to pale colours
Mixing Ratio: 1:1
Induction Time: Approximately 1 hour
Required Coats: 2
Recoat: Approximately 2–3 hours when dry and non-tacky
Coverage: Approximately 6 m²/L
Pot Life at 25°C: Approximately 6 hours
Minimum Application Temperature: 24°C (75°F)
Return to Service: Minimum 5 days
Application: Brush, high-density foam roller or spray
Cleanup: Klenk's Epoxy Thinner
Properties: Abrasion and water resistant

Frequently Asked Questions (FAQ's)

What is Klenk's Epoxy Enamel used for?

Klenk's Epoxy Enamel is a two-component coating designed primarily for refinishing bathtubs, sinks, toilets, ceramic wall tiles and appliances.

Can I paint a bathtub with Klenk's Epoxy?

Yes. Bathtub refinishing is one of the primary applications for Klenk's Epoxy Enamel.

Can Klenk's Epoxy be used on tile?

Yes. It can be used on ceramic wall tile when the surface is properly prepared and compatible with the epoxy.

Can it be used on fibreglass tubs?

Klenk's lists fibreglass among the hard, solvent-resistant surfaces that can be coated. Always test the surface with Klenk's Epoxy Thinner before application.

Can Klenk's Epoxy be used on plastic?

Plastic surfaces may be damaged by the solvents in the product. Test an inconspicuous area with Klenk's Epoxy Thinner before attempting to coat plastic.

Can it be used on a stove top?

No. Do not use Klenk's Epoxy Enamel on stove tops or other surfaces exposed to excessive heat.

How many coats of Klenk's Epoxy are needed?

Two coats are normally required. Additional coats may be necessary when covering dark colours.

What is the mixing ratio?

Mix one part Epoxy Catalyst with one part Epoxy Paint for a 1:1 mixing ratio.

How long should it sit after mixing?

After thoroughly combining Parts A and B, allow the mixture to stand for approximately one hour before application.

How long is the pot life?

At approximately 25°C (77°F), the mixed epoxy has a pot life of approximately six hours.

How long between coats?

A second coat can generally be applied after approximately 2–3 hours if the previous coat is dry and no longer tacky.

How long before I can use the bathtub?

Wait at least five days after painting before using the refinished surface.

Can Klenk's Epoxy be rolled?

Yes. Use a high-density foam roller. Roller application can create an orange-peel texture, so the surface can be lightly tipped off with a brush for a smoother appearance.

Can Klenk's Epoxy be sprayed?

Yes. The epoxy can be sprayed using the same 1:1 mixing ratio. Klenk's instructions state that thinning is not required.

Can Klenk's Epoxy be brushed?

Yes. A clean 1-inch brush designed for epoxy coatings can be used.

What is the coverage?

Coverage is approximately 6 m² per litre. Klenk's states that a one-litre kit provides enough material for approximately two coats on a bathtub, sink and toilet.

What temperature should it be applied at?

Maintain a minimum room temperature of 24°C (75°F) during painting and for at least 24 hours afterward.

What finish does Klenk's Epoxy have?

Klenk's Epoxy Enamel produces a hard, high-gloss epoxy finish.

Can Klenk's Epoxy be tinted?

Yes. The standard product is white and can be tinted to pale colours.

How do I clean a refinished bathtub?

After the epoxy has fully cured, use a mild cleaner such as diluted dishwashing liquid. Avoid abrasive, solvent-based and caustic cleaners.

Can I use a bath mat afterward?

Do not use a bath mat for the first month after refinishing. After one month, remove the mat after each use rather than leaving it on the surface.